Tag: Apple MacBook Pro

Let’s Rebuild The M1 Touchbar, Keys and Replace The Screen

Teardown and Rebuild M1 Touchbar

M1 Update – Touch bar

Take your time! I can’t stress this enough. This process of building this feature article, the M1 Touchbar, will require time, patience and a steady hand. It is important to take your time and proceed with caution. The article includes over 50 steps, so proper case is essential. If needed, consider seeing a professional help. There are easier alternatives available, but they may be more expensive.

For example, you could purchase the correct make/model upper case where the touch bar does not need to be removed and replaced.  However, finding the right parts may not be as simple as it seems, especially for a model that is just coming out of warranty. This challenge is common when repairing newer or cutting-edge electronics. In some cases, it may be easier to purchase a new computer, second-hand computer and replace only the parts from the existing machine.

Keep Your Work Area Clean, Clean As You Go

We clean up as we go, there were glass fragments before, during and after this process. Handle with caution and care. Glass and debris (dirt, hair, fuzz etc.) must be cleaned up as you go. The goal is to leave it better than the you found it! Ditto on Teardown. The same goes for the battery, battery cable, main screw, hinges, LCD cables, display, display hinge covers, cables (springs), antenna cables and assembly, LCD, remove antennae, main hinge screws, and remove LCD. First, perform an LCD check to ensure the new LCD works.

Disassemble Upper Cables

Starting here with the upper disassembled, we have the main logic board, power brackets, cable brackets. We need to disconnect the trackpad, speakers, logic board flex screws and cables. This is where we can begin the touch bar assembly replacement. Everything is bundled up, with covers, varying screws, and electronics tape. It is important to have your replacement ready once you have removed the main board, speakers, and trackpad. This is where things get tricky!

Continue Disassembly & Board

It’s handy to have your tool kit out. If not, give Amazon a quick call or pull up iFixit and scroll. You’re going to need adhesive remover, gloves, and glasses you know, the essentials when working with glass, and chemicals on small electronics.

We will start with the flat pry bar on the front (assuming all touch bar parts have been dismantled or ‘torn down’). We will slowly pry and spray our adhesive remover down behind the touch bar glass and the metal upper. It’s more fun if you have more adhesive remover than what we had during the refurb process. Not much left after the mobile device teardowns a few months back.

Touchbar

Ok, so first we remove the glue, glass, and finally the touch bar on the front by accessing it through the upper back. Then, it’s a simple process of replacing the touch bar. We need to be careful to remove the backing that will adhere the M1 Touchbar to the upper case, flex cable in hand through the upper or touch bar bracket and reassemble the touch bar cables and housing.

Throughout the rebuild process, we kept the screen protector film on to protect the screen. Below, you can find a number of images documenting each step of the process. Proceed with caution!

Touchbar Verification

Wrapping up, the M1 Touchbar has been installed, and all parts have been reassembled. Now let’s cover the conclusion. Once the machine is back together, a quick test is needed. We run the machine services mode, working with the drive, and checking what’s on it.

We wipe the main drive, rename it, rebuild it and reinstall it. Some quick terminal snippets and a reboot later, the process is complete. Once reinstalled, we remove any all all software (bloat) that we can, and we are off to the races. This laptop will be used at some point to run ham radio software, so I am hoping to install Linux on the main drive and use it as I have done with my previous machines. Well, that concludes the refurbish process/effort. If you have any questions, feel free to send me an email, Cheers.

Series Complete, Review Previous Posts

Lastly, good luck with your own Self Service Repair, and the same goes for the Parts catalog – https://selfservicerepair.com/en-US/home. The build continues on the M1, so be sure to check out the subsequent articles (5 in total)  M1 Refurb, Visual Inspection and Teardown,  M1 Touchbar, and Screen & Keys. Enjoy!  A friendly reminder,  It’s vital in my opinion to use OEM parts. IMO (in my opinion), if you can’t, consider second -hand options via Amazon or eBay. Additionally, the parts list is very helpful for those familiar with the process. If you’re not, don’t hesitate to reach out if you’re in a pinch. I’m happy to help or help guide you to the right support method or service.

We Teardown And Rebuild An Apple M1 MBP

M1 Teardown – Screen & Keys

M1 Arrow Key, LCD

LCD and keys, can be tedious, be careful and be aware of the process; ‘teardown’ process.

Visual Inspection, Keys

Starting with the easiest part of the refurbishment process – what is the easiest part of the build? The keys. Keys, Screen/LCD and then the touch bar. Please note, the refurbishment process required two teardowns, so to speak. First, let’s verify the working parts and inspect the touch bar on it’s own. The process, you could say, is a one-step job. However, I did this job in two parts for the sake of my own sanity.

The key here, is this: I know that if I could get the screen working, we would be in good shape. Cost aside, I was trying to avoid purchasing the M1 upper case which holds all parts associated with the computer. So, in other words, it’s a no-brainer,  keys on the keyboard, LCD screen, then touch bar.

Teardown

Internal Repair, Replace LCD

Start the teardown bell! We’ve completed our inspection and are beginning with the easiest of the three R/R (remove and replace) parts in this teardown. Keys can sometimes be tricky, so if you are familiar with them, please refer to the video below. If keys are a confusing concept to you, just focus on the left arrow key. There are several online resources available for reference, with Snazzy providing a helpful video walkthrough of the process. We breeze through the key change with ease.

For more detailed information, you can also  check out @SnazzyLabs, quick video on how to replace keys. It’s important to note – that there may be some differences between models, especially the M1. That’s why the video is so helpful! The key takeaway is that quick snap keys convenient but can tricky if you are not familiar with how scissor clips work. I recommend purchasing new keys (up, down, left and right) – make sure to get the ‘left arrow’ key) for a simple slide an click installation process. It’s as easy as pie.

Moving On To The Display

So, the cracked screen… We used a clamp tool and suction cups to get under the bottom case. A recommendation: iFixit has a variety of tools and parts for fixing things. We’ll talk more about them later, but we have bought a few items for them. You will also need adhesive remover, can you guess where we got ours? This is not a paid advertisement, but they have some great tools if you don’t have anything in your electric/technical toolbox.

We start by removing the bottom case when replacing the screen. Beginning with the batter cable for the M1 Screen & Key’s fix, it’s important to be carful as cables and parts are delicate and can easily break. So, remove the cable cover, battery cable, and screws. The most nerve-wracking part is dealing with the different sizes of screws, types of drivers, and prying tools required for the job (TORX, pryer(s), spudgers, tweezers etc). Once the battery cables and screws are removed, we can unscrew the hinge covers and move onto the antennas. It can be challenging to see the screws on the antennas, so good luck!

Teardown Upper, Goal LCD Removal

LCD Removal and Replace

The antenna will need additional cables, screws and bars leading down to the antenna and LCD springs. After installing those items, we will once again remove the antenna wire cover and detach the wires. It is important to exercise caution and be mindful of leaving the piece in better condition than when we found it. When removing covers, do so gently to keep glued area clean and free of debris (we had to address some glass bits). 

Teardown Continues With the Antennae and Cables

Once, the antenna bar is clear, the LCD hinge screws will need to be removed, along with the springs and mounting hardware. Voila, the LCD has been detached.

Antennae, Hinges and Test LCD

M1 Screen & Keys Wrap Up

This concludes the M1 Screen & Keys section of the refurbishment process. As mentioned earlier, we will now proceed to the touch bar. We went back, replaced all screws and cables to confirm that the LCD swap and key are working as expected, and we found that the touch bar was not working. We verified all parts (sans the touch bar) continued with wiping and cleaning in the following post. If you missed the first three articles, you can find those here: 1. Self Repair, 2. Refurb, and 3. Visual Inspection, Teardown. Cheers.